Especially where FEMA and Oshkosh and those other offtopic agencies that have nothing to do with music... are concerned...BTW the venue is responsible for any ASCAP/BMI dues and it's usually predicated on the number of seats :shock:
G
hello i just bought a drpa and not sure what the hell im doin.. here is what i have..
(2) B-52 mx1515
(1) 15\" kappa pro 15lf in avatar box
crown xls 602
carvin dcm1000
trying to figure out how to set up this rig.. if anyone has any ideas for me that would be great... also should i get that RTA-M Mic.. would it help.. should i spend the cash to get it..
here are the specs for the speakers and powers...
B-52 MX1515
SPECIFICATIONS
Nominal Impedance: 4 ohms
Frequency Response: 40-19k hz
High-Freq. Dispersion: 90 x 40
X-Over Points: 1.6k hz
Power Handling: 600 watts
SPL @ 1w1m: 99 db
Peak SPL: 130 db
Dimensions (W�x H� x D�): 19x45x18
Weight (lbs): 98 lbs
Avatar Cab with Eminence Kappa Pro LF 15
SPECIFICATION
Nominal Basket Diameter 15\", 381mm
Nominal Impedance* 8 ohms
Power Rating watts 600W
Music Program 1200W
Resonance 35Hz
Usable Frequency Range 38Hz-1.8kHz
Sensitivity*** 97.8
Magnet Weight 120 oz.
Gap Height 0.375\", 9.53mm
Voice Coil Diameter 3\", 76.2mm
THIELE & SMALL PARAMETERS
Resonant Frequency (fs) 35Hz
DC Resistance (Re) 6.5
Coil Inductance (Le) 1.40mH
Mechanical Q (Qms) 7.3
Electromagnetic Q (Qes) 0.32
Total Q (Qts) .30
Compliance Equivalent Volume (Vas) 198.8 liters / 7.0 cu. ft.
Peak Diaphragm Displacement Volume (Vd) 507cc
Mechanical Compliance of Suspension (Cms) 0.20mm/N
BL Product (BL) 21.6 T-M
Diaphram Mass inc. Airload (Mms) 102 grams
Efficiency Bandwidth Product (EBP) 112
Maximum Linear Excursion (Xmax) 6.7mm
Surface Area of Cone (Sd) 856.3cm2
Maximum Mechanical Limit (Xlim) 18.0mm
Performance Sensitivity (volts RMS) for full rated power at 4 ohms,
XLS-202 0.725
XLS-402 1.025
XLS-602 1.26.
Frequency Response (at 1 watt) 20 Hz to 20 kHz 0.75 dB.
Phase Response (degrees at 1 watt)
at 10 Hz 10.
at 20 kHz +19.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power > 100 dB.
No weighting, below rated power > 95 dB.
Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 1 kHz < 0.5%.
Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB < 0.3%.
Damping Factor (8 ohm) 10 Hz to 400 Hz >200.
Crosstalk (below rated power)
at 1 kHz 82 dB.
at 20 kHz 58 dB.
Voltage Gain (at maximum output) 31 dB.
Carvin DCM1000
HT POWER AMP SPECIFICATIONS:
MODEL DCM1000
Bridged RMS Continuous
4½, (20-20k Hz, <1.0%) 1000w
8½, (20-20k Hz, <1.0%) 700w
Both Channels RMS Continuous
2½ (20-20k Hz, <1.0%) 500/500w
4½ (20-20k Hz, <1.0%) 350/350w
8½ (20-20k Hz, <1.0%) 225/225w
THD (Typical—1/2 power): 0.03%
Damping Factor: >400
Slew Rate: bridged mode >45v/µs
Sensitivity: (4½, Vms) 1.0 V
Signal to Noise Ratio: Above 100dB
Frequency Response: 20 Hz to 20kHz
(10 Hz & 40 kHz)
Input Impedance: >20K ½, balanced
Comments
G
(2) B-52 mx1515
(1) 15\" kappa pro 15lf in avatar box
crown xls 602
carvin dcm1000
trying to figure out how to set up this rig.. if anyone has any ideas for me that would be great... also should i get that RTA-M Mic.. would it help.. should i spend the cash to get it..
here are the specs for the speakers and powers...
B-52 MX1515
SPECIFICATIONS
Nominal Impedance: 4 ohms
Frequency Response: 40-19k hz
High-Freq. Dispersion: 90 x 40
X-Over Points: 1.6k hz
Power Handling: 600 watts
SPL @ 1w1m: 99 db
Peak SPL: 130 db
Dimensions (W�x H� x D�): 19x45x18
Weight (lbs): 98 lbs
Avatar Cab with Eminence Kappa Pro LF 15
SPECIFICATION
Nominal Basket Diameter 15\", 381mm
Nominal Impedance* 8 ohms
Power Rating watts 600W
Music Program 1200W
Resonance 35Hz
Usable Frequency Range 38Hz-1.8kHz
Sensitivity*** 97.8
Magnet Weight 120 oz.
Gap Height 0.375\", 9.53mm
Voice Coil Diameter 3\", 76.2mm
THIELE & SMALL PARAMETERS
Resonant Frequency (fs) 35Hz
DC Resistance (Re) 6.5
Coil Inductance (Le) 1.40mH
Mechanical Q (Qms) 7.3
Electromagnetic Q (Qes) 0.32
Total Q (Qts) .30
Compliance Equivalent Volume (Vas) 198.8 liters / 7.0 cu. ft.
Peak Diaphragm Displacement Volume (Vd) 507cc
Mechanical Compliance of Suspension (Cms) 0.20mm/N
BL Product (BL) 21.6 T-M
Diaphram Mass inc. Airload (Mms) 102 grams
Efficiency Bandwidth Product (EBP) 112
Maximum Linear Excursion (Xmax) 6.7mm
Surface Area of Cone (Sd) 856.3cm2
Maximum Mechanical Limit (Xlim) 18.0mm
Crown XLS 602
XLS 602 Specifications: 2-ohm Stereo (per channel) 840W
4-ohm Stereo (per channel) 600W
8-ohm Stereo (per channel) 370W
8-ohm Bridge-Mono 1,200W
4-ohm Bridge-Mono 1,680W
Performance Sensitivity (volts RMS) for full rated power at 4 ohms,
XLS-202 0.725
XLS-402 1.025
XLS-602 1.26.
Frequency Response (at 1 watt) 20 Hz to 20 kHz 0.75 dB.
Phase Response (degrees at 1 watt)
at 10 Hz 10.
at 20 kHz +19.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power > 100 dB.
No weighting, below rated power > 95 dB.
Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 1 kHz < 0.5%.
Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB < 0.3%.
Damping Factor (8 ohm) 10 Hz to 400 Hz >200.
Crosstalk (below rated power)
at 1 kHz 82 dB.
at 20 kHz 58 dB.
Voltage Gain (at maximum output) 31 dB.
Carvin DCM1000
HT POWER AMP SPECIFICATIONS:
MODEL DCM1000
Bridged RMS Continuous
4½, (20-20k Hz, <1.0%) 1000w
8½, (20-20k Hz, <1.0%) 700w
Both Channels RMS Continuous
2½ (20-20k Hz, <1.0%) 500/500w
4½ (20-20k Hz, <1.0%) 350/350w
8½ (20-20k Hz, <1.0%) 225/225w
THD (Typical—1/2 power): 0.03%
Damping Factor: >400
Slew Rate: bridged mode >45v/µs
Sensitivity: (4½, Vms) 1.0 V
Signal to Noise Ratio: Above 100dB
Frequency Response: 20 Hz to 20kHz
(10 Hz & 40 kHz)
Input Impedance: >20K ½, balanced
We will ignore this post and work with you on the other thread you started...
Cheers,
Kevin